I have a couple of test flights behind the back and all is well, i.e. everything now works as it should.

Points to be observed in these test flights were to the effect of :

• MCP and Efis with FSLabs driver;
• MIP-functions with FSLabs driver;
• Flight Controls;
• CDU with PMDG driver;
• Throttle Quadrant with SIOC-driver (trust levers, speedbrake lever, reversers, cutoff levers, parkingbrake, flaps, TO/GA buttons, A/T Disconnect buttons);
• Avionics (radios);
• Warning lights and annunciators with FSLabs driver;
• Frame rates;
• ButtKicker.

In the beginning there were a few problems with o.a. the reversers, which made for landing congestion but the opposite that they had to do. M. a.w. holder de bolder on the runway past ...
After a proper calibration now work the reversers back to normal.

The trust levers of the TQ were in the beginning what to sore. The trust was open at the time that I'm on the rudderpedals came...
So a X-Control problem. Afterwards, at the rudder of this X-Control off the rudder and TQ now works as it should.

Also the gear lever was not working properly. He worked the other way round than in FS. Gear-up gear-down in FS . A connector on the ICS-system was just the other way around on the board and pinned. Turn over and solved !

The ButtKicker also had strange cures. Nothing shaking but the rattle against the stars. After checking it turned out that it had los gerammeld. I have the metal bevestigingsbalkje better screwed on and the trillerhefboom packed with cloths. The rattle is gone and the platform vibrates in the low bass. The epic centre is located between the two cockpitstoelen.

.

.

.

.

.

.

.

.

The very first visitor with the current full cockpit-configuration is in operation. The son himself, and rightly so.

Kenny has all of his father i.e. also a lot of interest in aircraft, aviation and flightsim.

.

.

.

.

.

.

.

.

An other important hardware, outside of the flightdeck hardware, computer setup and configuration of the different monitors.

The number of computers that are needed to the cockpit to send it ? The number of monitors and their displays that need to be adjusted ...

Hocus Pocus Pats ! And all of the displays of lights on ! (But it Was so easy).

The story is found on page PC Setup/Configuration.

.

.

.

.

.

.

.

.

When I give someone my address, say from this site I get always the same answer:"How do you say ?’ or ‘Say that again’ or ‘I can't remember, write’.

In order to resolve this issue, I have Business Cards (name Cards) in Vistaprint.

To order Online, not too expensive and easy. So done with repeat or to write ...

.

.

.

.

.
.

• Computer setup with peripherals;
• Purchase beamer;
• Connection backlighting MIP to button Lower Dimming Panels;
• Installation backlighting Lower Dimming Panels;
• Connection backlighting Lower Dimming Panels power Lower Dimming Panels;
• Connection backlighting TQ to button Lower Dimming Panels;
• Installation of indirect lighting glarewings and glareshield and connection to button Lower Dimming Panels;
• Finish Lower Dimming Panels (improvement board and fake-ventilation).

• Alu Rails
• Checklisthouders side of the TQ
• Clipboard yoke
• Finished seats

More photos on page Gallery.

.

.

.

.

.

.

.

.

Whew! This was a work of long breath. I have little or no input in. This was all with intermediaries. All real specialists in their field.

Danny and Nol for sanding and painting. Marc for the leather trim and badges. Yvette to the pillows to re-upholster and the badges. All vriendendiensten, so gr.... !

To everyone : Job well done !

More info about this on the page Hardware/Seats.

.

.

.

.

.

.

.

.

Between the TQ and the CDU-stand there is an opening since the TQ is not 100% connect with the CDU bay.

This beautiful seal, I have the opportunity to be on the sidepanels checklisthouders. So 2 boxes in which your documentation can put.

More info about this on the page Hardware/Throttle Quadrant.
.

.

.

.

.

.

.

.

.

To the track of the cockpitstoelen to be able to use I that what need to be customized and subsequently more refined with an aluminium cladding.

More info about this on the page Hardware/Seats.

.

.

.

.

.

.

.

.

.